Avid Technology Stage 48 Dokumentacja Strona 1

Stage 48for VENUE SystemsPN 9320-65036-00 REV B 2/12

Chapter 2: Overview 5Chapter 2: OverviewThis section describes the front and back panel features of Stage 48, and the front panel features of the Ethe

Stage 486Snake Act and Sig LEDsEach primary and redundant snake connection has its own Ac-tivity (Act) and Signal (Sig) LEDs. The system is ready for

Chapter 2: Overview 7Stage 48 Back PanelPower SwitchThe Power switch applies power to the Stage 48.AC Power ConnectorThe AC power connector accepts a

Stage 488Ethernet Snake CardThis section describes the front-panel features of the Ethernet Snake card. The Ethernet Snake card is installed in SC48.E

Chapter 3: Connecting Stage 48 9Chapter 3: Connecting Stage 48This section describes how to connect and power up the com-ponents of your system, and h

Stage 48103 Connect the included IEC power cable(s) between the Power connector(s) on any Stage 48 units present and your power source.4 Press the P

Chapter 4: Configuring and Installing I/O in Stage 48 11Chapter 4: Configuring and Installing I/O in Stage 48This section shows how to configure remot

Stage 4812Removing I/O Cards from SC48SC48 Stage I/O cards that you want to relocate to one or to two Stage 48 units can be removed from SC48 prior to

Chapter 4: Configuring and Installing I/O in Stage 48 138 Mark the cable end “A.” This will allow the cable to be easily identified when the Ethernet

Stage 48145 To lock the Top Panel in the vertical position, tighten the two interior captive thumbscrews located on the top left and top right sides

Legal NoticesThis guide is copyrighted ©2012 by Avid Technology, Inc., (hereafter “Avid”), with all rights reserved. Under copyright laws, this guide

Chapter 4: Configuring and Installing I/O in Stage 48 15Installing I/O Cards in Stage 48After you have removed Stage I/O cards from SC48, or if you ha

Stage 48169 Secure each card to the front panel of Stage 48 using four front panel mounting screws.10 Inside Stage 48 via the open back panel, tight

Chapter 4: Configuring and Installing I/O in Stage 48 17Installing Stage 48 in a RackStage 48 can be installed in a standard 19-inch rack. When in-sta

Stage 4818

Chapter 5: Specifications 19Chapter 5: SpecificationsSupported Stage I/O Card Audio SpecificationsAI16 Analog Input CardAll measurements at Fs=48 kHz

Stage 4820XO16 Analog/Digital Output CardAll measurements at Fs=48 kHz with 150 Ohm source impedance and 600 Ohm load impedance, unless otherwise spec

Chapter 5: Specifications 21Power and Status LED IndicatorsStatus LED Indicator(Stage 48 and Ethernet Snake Card)The Status LEDs on the Ethernet Snake

Stage 4822

23Appendix A: Compliance InformationEnvironmental ComplianceDisposal of Waste Equipment by Users in the European UnionThis symbol on the product or it

Avid2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USATechnical Support (USA)Visit the Online Support Center at www.avid.com/supportProduct In

Safety ComplianceSafety StatementThis equipment has been tested to comply with USA and Canadian safety certification in accordance with the specificat

Contents vChapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 1: Introduction 1Chapter 1: IntroductionVENUE Stage 48 from Avid® is a configurable remote stage box for VENUE SC48 consoles that uses highly

Stage 482Operational RequirementsTemperature and VentilationVENUE devices should be operated away from heat sources and with adequate ventilation. Sta

Chapter 1: Introduction 3Conventions Used in This GuideAll of our guides use the following conventions to indicate menu choices and key commands:The n

Stage 484